vrt

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 63 total)
  • Author
    Posts
  • in reply to: Fitting a passat ARB #8356
    vrt
    Participant

    Are arb’s still avaliable?

    in reply to: Corrado haldex #8329
    vrt
    Participant

    Just picked up a piece for the swap. It’s the tabs used to hold the driveshaft.
    Looks like the project is back into the slow mode again
    Picture.sized.jpg

    in reply to: Corrado haldex #8259
    vrt
    Participant

    Here is some more photo’s of what was done to the left and right side of the rails. Much clearer photos
    168637_1861229811457_1262284913_2237482_7244414_n.jpg
    180525_1861228771431_1262284913_2237480_2582563_n.jpg

    in reply to: Corrado haldex #8258
    vrt
    Participant

    So the filler neck doesn’t fit perfect. the bolt holes don’t line up so I have to make new holes or make some type of adapter to fit into the original holes.
    stay tuned

    also forgot to add. Looks like no one had a proportional valve on their cars. So were to place it now that the haldex is in place is tricky. I think I found a way around it. I hope to have pics of this tomorrow

    in reply to: Corrado haldex #8235
    vrt
    Participant

    Yes it didn’t take long once they got moving.
    The rear axles have then shortened

    in reply to: Corrado haldex #8213
    vrt
    Participant

    No comments??

    in reply to: Corrado haldex #8205
    vrt
    Participant

    Picture_034.sized.jpg

    Picture_035.sized.jpg

    Picture_036.sized.jpg

    Picture_037.sized.jpg

    Picture_040.sized.jpg

    Picture_041.sized.jpg

    in reply to: Corrado haldex #8204
    vrt
    Participant

    floor is now in and seam sealed

    Picture_029.sized.jpg

    Picture_030.sized.jpg

    Picture_028.sized.jpg

    Picture_033.sized.jpg

    in reply to: Corrado haldex #8203
    vrt
    Participant

    Picture_026.sized.jpg

    Picture_027.sized.jpg

    Picture_025.sized.jpg

    in reply to: Corrado haldex #8201
    vrt
    Participant

    Once the floor is all in place. Next will be getting a hole for the fuel system
    Like this photo
    00035_G.jpg

    in reply to: Corrado haldex #8196
    vrt
    Participant

    Here are pics of the floor underneath. It still has to lower a bit

    Picture_022.sized.jpg

    Picture_024.sized.jpg

    Picture_016.sized.jpg

    Picture_021.sized.jpg

    Picture_017.sized.jpg

    in reply to: Corrado haldex #8195
    vrt
    Participant

    Picture_069.sized.jpg

    Picture_070.sized.jpg

    Picture_071.sized.jpg

    Picture_073.sized.jpg

    Picture_075.sized.jpg

    in reply to: Corrado haldex #8194
    vrt
    Participant

    I have lots of new pic to show what really need to cut cut out on the passanger side. There is a extra reinforcement on corrados that need to get cut out or trimmed back to help slid the side panel into place.

    The floor is now in it’s proper place. It’s been tacked into place so that we can test fit the subframe and make sure everything is level. Once it’s all ok. The crew will weld up everything tight

    in reply to: Corrado haldex #8187
    vrt
    Participant

    he corrado floor is out

    100_0608.sized.jpg

    100_0609.sized.jpg

    100_0611.sized.jpg

    100_0610.sized.jpg

    the new floor will be in place tomorrow. Seems that it’s not a perfect fit about 1″ on each side needs to be cut out so that it fits

    in reply to: Corrado haldex #8186
    vrt
    Participant

    ready to place into the car

    floor2.sized.jpg

    floor1.sized.jpg

Viewing 15 posts - 16 through 30 (of 63 total)

V2 of the vwsyncro.co.uk forums

Site and hosting by Plus8.net
Firebeans crystal healing (new wordpress site) | Firebeans crystal healing (old site)